Tool Functions

Nitro Owners Forum

Help Support Nitro Owners Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

JD Johnson

Well-Known Member
Joined
Jun 19, 2005
Messages
1,362
Reaction score
0
For those who may not be familiar with the functions of all these tools:



1. DRILL PRESS:

A tall upright machine useful for suddenly snatching flat metal bar stock out of your hands so that it smacks you in the chest and flings your beer across the room, splattering it against that freshly painted part you were drying.



2. WIRE WHEEL: Cleans rust off old bolts and then throws them somewhere under the workbench with the speed of light. Also removes fingerprint whorls and hard-earned guitar calluses in about the time it takes you to say, "Ouch ..."



3. ELECTRIC HAND DRILL: Normally used for spinning steel pop rivets in their holes until you die of old age



4. PLIERS: Used to round off bolt heads.



5. HACKSAW: One of a family of cutting tools built on the Ouija board principle. It transforms human energy into a crooked, unpredictable motion, and the more you attempt to influence its course, the more dismal your future becomes.



6. VISE-GRIPS: Used to round off bolt heads. If nothing else is available, they can also be used to transfer intense welding heat to the palm of your hand.



7. OXYACETYLENE TORCH: Used almost entirely for lighting various flammable objects in your garage on fire. Also handy for igniting the grease insidea brake drum you're trying to get the bearing race out of.



8. WHITWORTH SOCKETS: Once used for working on older British cars and motorcycles, they are now used mainly for impersonating that 9/16 or 1/2 socket you've been searching for the last 15 minutes.



9. HYDRAULIC FLOOR JACK: Used for lowering a motorcycle to the ground after you have installed your new front disk brake setup, trapping the jack handle firmly under the front fender.



10. EIGHT-FOOT LONG DOUGLAS FIR 2X4: Used for levering a motorcycle upward off a hydraulic jack.



11. TWEEZERS: A tool for removing wood splinters.



12. PHONE: Tool for calling your neighbor to see if he has another hydraulic floor jack.



13. SNAP-ON GASKET SCRAPER: Theoretically useful as a sandwich tool for spreading mayonnaise; used mainly for getting dog-do off your boot.



14. E-Z OUT BOLT AND STUD EXTRACTOR: A tool that snaps off in bolt holes and is ten times harder than any known drill bit.





15. TIMING LIGHT: A stroboscopic instrument for illuminating grease buildup.



16. TWO-TON HYDRAULIC ENGINE HOIST: A handy tool for testing the tensile strength of ground straps and brake lines you may have forgotten to disconnect.



17. CRAFTSMAN 1/2 x 16-INCH SCREWDRIVER: A large motor mount prying tool that inexplicably has an accurately machined screwdriver tip on the end without the handle.



18. ELECTROLYTE TESTER: A handy tool for transferring sulfuric acid from a car battery to the inside of your toolbox after determining that your battery is dead as a doornail, just as you thought.



19. AVIATION METAL SNIPS: See hacksaw.



20. TROUBLE LIGHT: The mechanic's own tanning booth. Sometimes called drop light, it is a good source of vitamin D, "the sunshine vitamin," which is not otherwise found under motorcycles at night. Health benefits aside, it's main purpose is to consume 40-watt light bulbs at about the same rate that 105-mm howitzer shells might be used during, say, the first few hours of the of the Bulge. More often dark than light, its name is somewhat misleading.



21. PHILLIPS SCREWDRIVER: Normally used to stab the lids of old-style paper-and-tin oil cans and splash oil on your shirt; can also be used, as the name implies, to round off Phillips screw heads.



22. AIR COMPRESSOR: A machine that takes energy produced in a coal-burning power plant 200 miles away and transforms it into compressed air that travels by hose to a Chicago Pneumatic impact wrench that grips rusty bolts last tightened 40 years ago by someone in , and rounds them off.



23. PRY BAR: A tool used to crumple the m
 
Hey... what've you been doing snooping around my garage?
 
26. MECHANIC'S KNIFE: Also used to cut past my shirt into my stomach and me to macho to go have stitches so I call me wife and tell her to pick me up some of that new "skin glue". Thats right, happened last week to me but instead of having a regular blade it had a shingle hook which is much sharper and cuts just as deep into the human belly..



Jeff
 
Sim, I don't know what he's being doing in your garage,,, But, he has been in mne for sure!
 
Something must be wrong with the saw.....I've cut this board 3 times and it's still too short. :wacko:





:lol:Harpo
 
SoonerFan

Get ya a good set of board stretchers, I think Lowes has them on sale this week.
 
Back
Top