durangod
Member
For those that do not know the 1988 bass tracker is an all fiberglass boat, in the early years they tried their hand at it i guess and then went to all aluminum.
Long story short, the floor is rotted.
Something else i have learned is that in the old days of boating (80's) open cell foam was really all they had to use and it was affordable. Open cell foam soaks up water and can add at least 400 lbs to a bass boat, it does not dry out and it rots the wood. So the rule of thumb is that if you see open cell foam, remove it and throw it away and refoam with closed sell marine foam. Not as easy as it sounds as there are some places you just cant get to on a bass boat (in particular an older fiberglass boat) as i have.
The top cap is one solid molded piece of fiberglass and so is the bottom, then they are mated together. I have seen vidoes of removing the cap to totall remove the whole floor. But that can be very dangerious and costly.
First you could end up cracking the cap in places you wont notice till you get it on the water. Then you have to have someplace to store both pieces while you work on them, then once you remove the cap the bottom will tend to spread out and that means you may never get the cap to fit exactly right ever again.
So for now i am forced to replace what i can see (and get to) and leave the rest alone. Everything under the rear storage and live wells i know is toast but ill have to live with it for now.
Foam does three things, floatation, takes up space that the water would normally take up, and adds strenth and rigidness to the boat. So i will refoam what i can with marine foam that ill never have to replace again.
As far as the wood, ill never use normal plywood again. I am going with 1/4 marine HDPE sheets, in simple terms plastic wood. It comes in 4x8 sheets, will never rot, will never soak up water, is very strong and durable and is the perfect replacement for plywood in a boat IMO. Comes in many colors, im using black. The only down side to it is that it cant be painted. So ill have to put my fiberglass cuttings back to cover it up then paint the fiberglass. I dont know if fiberglass will stick to HDPE or not, i hope so.
So with the new foam that will never soak up water and the HDPE that will never soak up water, ill never have to do this job again unless i get access one day to the parts that i left out this time.
So thats the plan. for now hee hee
I cant wait until the demolition is done so i can start puting this thing back together again.
Long story short, the floor is rotted.
Something else i have learned is that in the old days of boating (80's) open cell foam was really all they had to use and it was affordable. Open cell foam soaks up water and can add at least 400 lbs to a bass boat, it does not dry out and it rots the wood. So the rule of thumb is that if you see open cell foam, remove it and throw it away and refoam with closed sell marine foam. Not as easy as it sounds as there are some places you just cant get to on a bass boat (in particular an older fiberglass boat) as i have.
The top cap is one solid molded piece of fiberglass and so is the bottom, then they are mated together. I have seen vidoes of removing the cap to totall remove the whole floor. But that can be very dangerious and costly.
First you could end up cracking the cap in places you wont notice till you get it on the water. Then you have to have someplace to store both pieces while you work on them, then once you remove the cap the bottom will tend to spread out and that means you may never get the cap to fit exactly right ever again.
So for now i am forced to replace what i can see (and get to) and leave the rest alone. Everything under the rear storage and live wells i know is toast but ill have to live with it for now.
Foam does three things, floatation, takes up space that the water would normally take up, and adds strenth and rigidness to the boat. So i will refoam what i can with marine foam that ill never have to replace again.
As far as the wood, ill never use normal plywood again. I am going with 1/4 marine HDPE sheets, in simple terms plastic wood. It comes in 4x8 sheets, will never rot, will never soak up water, is very strong and durable and is the perfect replacement for plywood in a boat IMO. Comes in many colors, im using black. The only down side to it is that it cant be painted. So ill have to put my fiberglass cuttings back to cover it up then paint the fiberglass. I dont know if fiberglass will stick to HDPE or not, i hope so.
So with the new foam that will never soak up water and the HDPE that will never soak up water, ill never have to do this job again unless i get access one day to the parts that i left out this time.
So thats the plan. for now hee hee
I cant wait until the demolition is done so i can start puting this thing back together again.
