Search results

Nitro Owners Forum

Help Support Nitro Owners Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. O

    Tracker Grizzly Badly Oxidized

    .you can try a buffer with polishing compound [like for a car] and cut with paint thinner . did this on and old 1975 camper van , made it look like new.
  2. O

    Am I The Only One?

  3. O

    Am I The Only One?

    olefisherman mine is nitro160 rick clune . a 95 with 60 hp merc .
  4. O

    Have A 95 Nitro 160

    does anyone know how to access the thru hull puck for driver seat fish finder without removing gas tank ? please help.
  5. O

    Hatch For Center Step In Nitro 160

    posted a question about cutting out rear center step on a nitro 1995 160 rick clune edition seems no ne has even an opinion about how this can be done or even if its advisable. thanks for nothing. see u:(
  6. O

    A Question

    where is the puck for drivers depth finder located in relation to the floor drain in a nitro 160 1995 model rick clune edition
  7. O

    Hatch For Center Step In Nitro 160

    more info for center space between seats step . drivers fish finder only works if there is a few gallons of water in bilge . want to access puck to re epoxy to hull. then convert the cutout step to hatch cover. the only way to reach the area is to remove the gas tank and then morf into a snake...
  8. O

    Hatch For Center Step In Nitro 160

    in thinking I want to cut out the center step between the seats and make the space into a compartment using the cutout as hatch cover . nay one ever done this ?any suggestions will be appreciated and all comments considered.
  9. O

    Rev Counter

    all of a sudden my rev counter is showing 7000 rpm at full throttle, normally it was about 5000 what could cause this?
  10. O

    No Power

    to the running lights in bow same wireing was used to power fishfinder . now bow light no power to new garmin . worked last night but not this morn. are there fuses to look for? 1995 nitro 160 rick clune model
  11. O

    Okay...."Old NTOWS Folks" check in

    olefisherman still here and hoping for a better crappie season next spring. :)
  12. O

    2013 Z7 Rod Locker Organizer

    i diden't even look at dealers. went to hardware store ACE bought some pcv drain pipe [has thin wall]cut in pieces bundled and installed in forward part of rod locker.cant post pics , but i can send a pic to your e mail.
  13. O

    Hi From Nh

    welcome to the forum i have a 95 rc 160 i think is a great boat . bought from a dealer about 6 years ago . it was the dealers son's boat and shop maintained and garaged . when i first saw it i thought it was a new boat.
  14. O

    Oil Tank Draining

    why are you disconnecting the fuel line?with good gas treatment and running the motor on the muffs long enough to get it into the carbs you will have no trouble. at least thats what i have done the last 20+ years.
  15. O

    Hello From Michigan

    if this a glass boat you are talking about you should take a small rubber hammer and tap on the hull every where you can reach and especially on the transom . delamination of the glass hull is a serious problem .and transom rot is dangerous and expensive to fix. you will be able to hear the...
  16. O

    Depth Finder Not Working

    where can i find a thru hull transducer for a hummingbird sx100? or will the trolling moter transducer work thru hull ? wanting to move the 100sx to driver station and get a new unit for front seat.
  17. O

    Hummingbird Crazy

    thanks for the reply . hadn't thought to put the transducer any where but the factory location.
  18. O

    Hummingbird Crazy

    today turned on the fish finder tracker wide eye first it would not power up . my buddy says hold the power button down for 10 seconds , it will reset. did that it powered up . but the depth readings were way off. the depth was reading 32 ft. and the prop was chewing mud. can anyone say what...
  19. O

    Replacing A 4 Pin Connector On Trailer...

    happened to me . it was corroded connector pins in a round multi prong connector under the oil tank . 40 min each way, fixed in ten min
  20. O

    Best Way To Remove Corrosion On Trailer Axle Spindle

    crocus cloth from napa ,oreilly. or any other auto parts store.
Back
Top